Replacement is pretty straightforward, just unscrew the old hose and the showerhead then attach the new ones in place. I just made one minor modification to the new showerhead by drilling a bigger hole into the water saver valve (located on the water inlet of the showerhead) as the water flow is weak and restricted by the smaller hole.
Friday, March 4, 2016
RV Exterior Hand Held Hose/ Showerhead Replacement with Magnetic Pin Mount
I finally replaced my bulky, leaky, hard to store exterior showerhead and hose attachment. Found a small showerhead with built-in shut-off lever on Amazon along with a very flexible stainless steel hose, a shower pin wall mount (optional) and a pin mount swivel connector. Actually, the pin wall mount/ swivel connector was salvaged from an old showerhead I had, but it is available on Amazon (clickable Amazon links above).
Replacement is pretty straightforward, just unscrew the old hose and the showerhead then attach the new ones in place. I just made one minor modification to the new showerhead by drilling a bigger hole into the water saver valve (located on the water inlet of the showerhead) as the water flow is weak and restricted by the smaller hole.
Replacement is pretty straightforward, just unscrew the old hose and the showerhead then attach the new ones in place. I just made one minor modification to the new showerhead by drilling a bigger hole into the water saver valve (located on the water inlet of the showerhead) as the water flow is weak and restricted by the smaller hole.
The new hose is very flexible and really easy to store, unlike the factory hose which is a pain to store into the storage compartment, just coil the new hose about 3x and the door will close with ease.
With showerhead mounted on the existing pin mount.
The shower head lever locks open, it slides forward to lock when you fully depress it. To unlock, simply slide the lever back towards you.
Optional showerhead DIY magnetic pin wall mount. I just epoxied a strong circular magnet (usually available at your local home improvement store) on its backside then covered the magnet with felt fabric to prevent it from scratching the RV body paint.
With showerhead mounted high up. A good option if you enjoy showering outside, not that I'm looking forward too. But I can see it useful on the beach if you need to rinse off after surfing or swimming, especially here in California where state beach shower/wash stations are turned off due to the drought.
Showerhead mounted low to the ground, good for hand washing and rinsing your feet and minimizing splashing of water into the side of the RV.
To store the magnetic pin wall mount inside the exterior shower compartment, I attached a big metal washer into the right side wall using VHB tape.
With the magnetic pin wall mount stored.
Subscribe to:
Post Comments (Atom)
There are so many different shower heads on amazon. could you tell me more info on yours so I can find it? this mod is just what I need.
ReplyDeleteThe shower head, hose, and pin mounts links can be found above at the start of the post. Just click the underlined clickable links and a new Amazon tab/window should open. If for some reason clicking on the links does not work (i.e. pop-up is blocked in your browser), you can right click on the links and select "open in new tab" instead. Hope that helps.
DeleteLove this idea and I'm going to shamelessly steal it! Tell me please, the shower head you have appears to have a lever that must be depressed to activate the water, is that so? Does the lever lock open or must it be continuously depressed? Thanks!
DeleteNo problem :-). The shower head lever locks open, it slides forward to lock when you fully depress it. To unlock, simply slide the lever back towards you.
DeleteI also apologise to the very late reply, I was on a long trip and no connection where I was. Thanks.
DeleteNo worries, thanks for the reply. After I reread your post, I see where you specifically said "a small shower head with a built-in shut-off lever". My bad. The link you have to the magnet you used takes me to an Amazon page for a magnetic hook. Did you remove the magnet from the hook and use it on your wall pin mount?
DeleteYes, I removed the magnet from the hook and epoxied it on the wall pin mount. I will be removing that link from Amazon as it looks like it was changed and now seems overpriced. You can get it from Home Depot store for a lot lesser price and the correct size.
DeleteWell, 5 years later your idea is still the best one ever. Stole it, and totally unashamed. Haha. Ordered the exact same stuff with the exact same mounting....
ReplyDeleteNothing to be ashamed if it works, lol. I use the magnet mount lots, very convenient esp. With the kids.
DeleteHere are some updates you might want to consider:
DeleteFor the shower hose, I found this:
https://www.amazon.com/gp/product/B01N67DKKO/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1
It has a shower end head that rotates after you attach it, the other one did not seem to have this feature. It also comes with two protective covers for the chrome end fittings with screw on caps for the ends so you don't lose the washers included. It also comes with two extra washers. It is just as flexible as the other hose.
For the shower head pin mount, the link you have does not go to any specific product anymore. It is now a general info page for same products. I clicked one of those and received a mount with plastic pin which wouldn't make it long term. And, the plastic was loose which would be firm if mounted on a wall. For this application you would have to epoxy it to the plastic mount. I wound up buying the Delta chrome pin mount and the Delta chrome shower head connector from Amazon as a result. I am not sure why your connector says "swivel" in your description as the shower head connector from Delta doesn't swivel but the hose mentioned above does.
I think these are good updates and I am very pleased with the idea and the implementation I wound up with. Thanks again for the idea.
Rick
Thank Rick,
DeleteI will update the links that you mentioned, thanks for the info. The Delta pin mount does more like tilt instead of swivel, but that is how they describe them. Thanks again.
Love this mod. I used a 2" diameter 25lb pull magnet (https://www.homedepot.com/p/Master-Magnet-25-lb-Round-Base-Pull-Magnets-96324/203613132), epoxied a 2mm thick piece of felt (pic: https://a.cl.ly/mXu5x5p6), and it's magnetic but nowhere near strong enough to hold up the showerhead. What am I missing?
ReplyDeleteThanks. It appears that the felt you use is a little thick, no? If the magnet is rated for 25 lbs, then it should hold the shower head with no problem.
DeleteI managed to painstakingly rip and cut off the felt with my teeth and a razor blade, and a thinner piece of felt is the ticket! Avoid premium felt and get the stuff you can see through. Thanks!
Delete